Comments on: Labtec Ultra Flat Wireless keyboard and mouse

By: Symb

Symb — Tue, 27 May 2008 19:45:11 +0000

I have a very stupid problem. I got this keyboard and mouse set from another person and i cant get it to run. i press the connect button both on the receiver and keyboard but nothings happening. So my question is, how to start this thing…..

By: Dimiter

Dimiter — Wed, 14 May 2008 14:24:28 +0000

Hello people,
I have that utterly crappy problem with my mouse.
Whenever i 1 click smth the mouse sometimes just double or triple clicks it.
I cant even underline a text with my mouse because when i hold the button underline the text and i release the button it reacts like if i have just double clicked.

Anyone has the same problems and have you found a solution for this ?

Thank you in advance,
Dimiter

By: zac

zac — Sun, 11 May 2008 12:35:30 +0000

Pros: looks great, very good flat buttons, cheap
Cons: doesn’t work very well with games (especially shooters), mine for some reasons mutes the pc by itself for no apparent reason

If you don’t play games and sound isn’t very important you should buy it; otherwise stay away from it.

By: waji

waji — Sun, 04 May 2008 13:00:10 +0000

is good

By: NabDenceceTal

NabDenceceTal — Mon, 31 Mar 2008 14:03:46 +0000

E-gold is gradually leaving, who’ll substitute it?
It’s was a time when I was using e-gold everywhere but after all that problems and account freezing I’ve no trust to e-gold. Now I’m vacillating between pecunix and Perfect Money… But after Pecunix had been ddosed for a whole month I’ve got a wish to work only with Perfect Money.

By: Barbara Arbesser

Barbara Arbesser — Mon, 17 Mar 2008 11:19:43 +0000

Hi folks,

I’ve got problems with my keybord…It’s ddoubeeling letters as you can see.. I changed rrepeaat rrate and batterriees alrready… wwhat can I do?

thankss!

By: donralfo

donralfo — Thu, 27 Dec 2007 16:57:40 +0000

This is the worst product I have ever bought… useless… after a few minutes the keybord and mouse stops working, it’s like the reciever forgets that it’s connected! I have to push the connect button on the keybord and mouse every 2 minutes otherwise it won’t work….
The problem is that i bought this product online, and it cost 10£ to send it back for repair.. i only bought it for 20£… it’s garbage…

Can anyone help if it has anything to do with drivers ect.

By: Peter Vida

Peter Vida — Sat, 10 Nov 2007 15:49:59 +0000

Yo!
I’ve bought this package.
This seems very modern at its nice…
But i can’t connect them to the computer…
I did all the things what the paper wrote to do…but its still doesen’t work…
At least now i don’t have the install-disc too
If u can help me write please:
trigger7@freemail.hu

By: zaidi

zaidi — Mon, 13 Aug 2007 15:43:26 +0000

hello everyone,

i have also owned this keyboard/mouse for about 3-4 months now… bought it for only 10£ so cant complain much about the problems, although it do give me problems as well but i have found workaround for them, i m writing them below so maybe someone might take advantage..

first of all go in to the system bios and change system bios setting from fast boot to normal (this gives adequte time to check all system components at post and reduces keyboard/mouse failure errors)

when the system boots keep an eye on ir receiver leds they MUST FLASH if they dont just poweroff wait for 1-2 seconds and poweron again if not then repeat the same prodedure again untill u do get an led flash

keep an eye on bios messages, if u see errors on post like keyboard failure or auxillary device failure just poweroff again wait 1-2 seconds and poweron, there shouldnt be any such messages either.

when system is being loaded keep moving the mouse up n down i have observed if u leave the mouse idle at boot up it will probably stuck up and wont respond no matter how many times u press connect..

if u setting up connection for the first time always configure keyboard first. press connect on the receiver after 1-2 seconds press connect on keyboard.. now keyboard should work.. then press again connect on ir receiver and after 1-2 seconds press connect on mouse dont worry if nothing happens just restart the system making sure u r moving the mouse up n down… 95% of the time it works normally 5% u have to reboot again..

i have also observed once the setup is up n running for sometime it wont trouble u if u keep eye on startup ir leds and bios messages.. avoid pressing connect again n again once the connection is established.. even when mouse donot work on some occasions..

i m not much of a 3d gameplayer so i never came across problems with keyboard, but recently i played doom3 and it gives problem of not stopping going ahead when u press w..

anyway do add ur experiences i hope i helped a bit..
regards

By: robb

robb — Tue, 07 Aug 2007 15:20:44 +0000

**FOR LINDA**

hold the connect button on the reciever for about 3 seconds and then hold the connect button on the keyboard so both buttons are being held at the same time.

Hold them both for about 15 seconds.

then wait a while and see if it works.

if it doesnt work, then keep trying.

if THAT doesnt work then take it back to the shop.